Quick Winter Energy Saving Tips

The chilly winter season is upon us and it is a good time to think about how we can make our homes more energy efficient. Not only will it save money on your electric bill but will help you live a greener lifestyle and be more comfortable. Fortunately, none of these steps are overly burdensome or expensive.

The first one is to plug up the leaky spots around your home. If you have never thought about how heat might escape your house, you probably have numerous spots where cold air is able to rush into the living space. A common area is under outside doors where the seal has become ineffective and no longer blocks the outside air. Additionally, the weatherstripping around the remainder of the door can fail allow cold air to seep in. You can easily purchase replacement weatherstripping at a home improvement store and follow the directions to install it. Be sure to caulk gaps or cracks around the door frame. Often cold air can reach the interior of the wall through these cracks and find its way into your living space.

Consider expanding foam spray if you find larger holes or cracks that can't be filled in with caulk. One brand name is Stuff. Basically, it is a liquid that rapidly expands and then hardens. I found that it worked well to block a hole underneath my door threshold that was large enough to actually see through. Plus, the foam prevents insects and mice from entering your home.

Next, cold air can enter your home through outlets on outside walls. Check for drafts around yours and buy specially designed foam inserts to block the air flow. They are not visible when installed properly.

Windows are a huge concern for conserving energy. You can reduce the amount of heat escaping your home by covering each window with plastic. The plastic creates dead air space over your windows and retards heat loss while allowing light to enter. An alternative is to keep your drapes open on windows that are facing the sun. This way you put the sun to work heating your home. However, you have to keep all other windows draped over to prevent heat from escaping. By not covering your windows you are allowing up to 20% of heated air to escape.

Finally, technology can really help out. Consider installing a programmable thermostat. These devices can be set to only heat and cool your home when you are home. While you are away at work the thermostat can let the temperature in the winter drop ten degrees and then warm up again right before you come home. In this fashion you are not fully heating an empty house and incurring the cost. A qualified heating and cooling specialist such as Abel Onsite can advise you on this topic.

These are just a quick tips to think about. Hopefully they will help you easily save money each month on your power bill.

For more energy saving tips visit Abel Onsite or call 952.446.9545 today . Article independently authored by Eric Parish. The content herein may or may not reflect the views and opinions of Abel Onsite. Click for search engine optimization and search engine marketing or visit WebDrafter.com's Blog.

Authorized Air Sealing & Weatherization Contractor

Abel Onsite is now Authorized by Honeywell and certified by the Building Performance Institute (BPI) to perform air sealing and weatherization for homes and buildings

As an authorized Honeywell Weatherization Contractor, Abel Onsite is now providing services to make homes, buildings more energy-efficient.

Saint Bonifacius, MN – November 2010 – ABEL ONSITE, the heating and air conditioning specialists, announced that it has been authorized by Honeywell to provide air sealing and weatherization services for homes and commercial buildings. As part of their training, key employees at Abel Onsite have also received their Building Analyst and Building Envelope certification by the Building Performance Institute (BPI) which teaches them to take a comprehensive “House as a System” and “Building as a System” approach to their weatherization projects.

To learn more view our full Press Release on our website "Click Here".

Five Reasons to Install a Solar Array

With all the talk of alternative energy on the news lately, you might begin to wonder how you can be a part of it. There are many ways to become involved from hybrid cars to geothermal heat and cooling. One of the best ways, however, is solar. In fact, here are five excellent reasons for installing solar panels on your home.

1) Save Money - Electricity rates have been going up for quite some time now and they are not expected to reverse this trend. In fact, some experts believe that electricity rates could skyrocket over the next few years. With solar, you insulate yourself from these problems. Once you install a complete system you never have to pay an electric bill again. That is a great feeling. Even if you install a system that only supports a portion of your needs, you are cutting down your electric bill each month.

2) Power Outages Don't Happen - If you have ever lived through a multi-day power outage you know how very inconvenient this is to put it mildly. With a complete solar array, you will always have power even if you neighbors don't (depending on how you have your array configured). You cut your dependency to the power company. In fact, this can feel liberating which might be yet another reason for solar!

3) Increase Your Home's Value - Solar is a very desirable item in the real estate market. Of course, if you intend to move very soon installing a solar system does not make sense. However, if you are going to spend many years in your home and ultimately desire to sell, it can increase your selling price. A 1998 study by ICF Consulting found that a solar system that saves $1,000 per year on electric bills increases the home's value by $20,000.

4) Protect the Environment - Solar power is renewable and does depend on fossil fuels. For this reason, solar is a clean technology. By investing in a solar array you are helping to make the earth a cleaner place.

5) Technology is Cool - This isn't an oft cited benefit but it is a reality. A solar array is a great conversation starter as people have a interest in it. Plus, if you have children or grandchildren it is a great live science experiment. Teaching about the various aspects of the system can lead into many interesting and educational conversations. By talking to people and your children you are helping to spread the word about solar power and helping the earth and others in the process!

Of course, solar power is a complicated subject with many aspects to consider. Take the first step and call an installer to see what if would take to install a small, starter solar system. Your pocketbook and the earth will be glad you did!

For additional information on the topic of solar power visit Abel Onsite. Article independently authored by Eric Parish. The content herein may or may not reflect the views and opinions of Abel Onsite. Click for search engine optimization and search engine marketing or visit WebDrafter.com's Blog.

Controlling Your Home's Humidity Level

While the South is well known for its high humidity -especially during the summer-it s not the only region of the U.S. where people have to deal with high humidity levels. For instance, when people in Colorado refer to the "dry cold" of the winter's mountain air they are talking about the humidity just as Miami's muggy, sticky heat is a result of humidity. Since humidity is no respecter of regions, it is often necessary to take control of the humidity level within your home.

The EPA recommends that the indoor humidity level be no more than 30-50% relativity humidity. This relative humidity is the amount of water vapor the air contains compared to the maximum amount it can hold at any given temperature. Consequently, if your indoor humidity level is too high, it should be controlled in one of two ways: by lowering the humidity level with a properly sized air conditioning system or by having a humidifier (or in some cases a dehumidifier) installed.

To effectively keep your home's humidity level comfortable by using an air conditioner, it is of utmost importance to have an AC unit that is the proper size for the amount of space to be maintained. If it is too big it will turn on and off too often and result in there being too much moisture in the air. Of course, during the winter months, when heaters are in use, the same rule applies. If your heater is too big, it will dry out the air so rather than having cold "clammy" air, it is dry and can often make breathing difficult.

How to Tell If You Need a Dehumidifier

If you are not sure whether or not you need a home dehumidifier, there are several signs that you can judge by:

• Wet stains on walls and ceilings
• Stuffy feeling in a room
• Rotting wood
• Condensation on windows
• Musty smells
• Allergies due to the air in your home being too moist which will encourage the growth of bacteria and mold

Additional Ways to Control Your Home's Humidity Levels

If you already have a dehumidifier but your home's air still has too much humidity for your liking, or are perhaps trying to put off the inevitable, there are several steps you can take to reduce the humidity level in your home. These include:

• Improving the drainage around your home's foundation by making sure that gutter downspouts put water away from the foundation; keeping gutters and downspouts clean and open; making sure that the soil slopes away from your home so that water does not pool around your home and by not overwatering plants near the foundation.
• Making sure that your clothes dryer is properly vented; not only will this improve the humidity level, but your clothes will drive faster.
• Using vent fans in the bathroom and kitchen to remove humidity where it starts.
• Repairing leaking faucets, this will save on your water bill and lower humidity!

For additional information on the topic of humidity and dehumidifiers visit Abel Onsite. Article independently authored by Janet M. Slagell. The content herein may or may not reflect the views and opinions of Abel Onsite. Click for search engine optimization and search engine marketing or visit WebDrafter.com's Blog.

The 3 Types of Solar Heating for Your Home

Are you looking for a way to lower your energy costs that is both efficient and environmentally friendly? With the rising cost of gas or electric heat, you may be looking for an effective alternative. Fortunately, there are several choices available, one of which is the use of solar energy.

Today there are 3 types of thermal solar collectors-low temperature, medium, temperature and high temperature. And while the names may not be all that original and the concept of solar heating is not brand new, there is still much to be gained by opting to use solar energy. The use of solar energy works on the principal that what is gotten out of a solar collector is the difference between what went into the collector and what the collector lost to its outside environment. What is left is used for heating.

Low Temperature Solar Collectors

A low temperature solar collector typically loses nothing to the outside air as it works below the outside air temperature. An example of is a solar swimming pool which is heated by hanging a black plastic mat out in the sun, run pool water through it and Viola! Your pool water is warmed. In this scenario, the black plastic will receive approximately 95% of the solar energy and the efficiency drops significantly. This principle can applied to heating the water in your home, by having metal panels that are filled with water built or installed to the outside structure of your home. The water travels through these panels to your home's plumbing system. You can even have built water filtration added to the system so you can enjoy cleaner, healthier water as well.

Medium Temperature Solar Collectors

This is actually the most commonly recommended form of solar energy for residential use. It works by trapping the sun's energy in an insulated box, typically located on the roof of a building. As outside temperature rise the collectors retain the energy in boxes made of aluminum, copper, foil and low iron tempered glass. Traditionally, as the sun hits the shingles in a non-solar heated home the heat passes through, get absorbed or is reflected. The solar boxes, however, collect this heat and store it as energy to be released as needed into your home. In fact, sometime, there is so much energy collected, that your meters will actually turn backwards meaning that you are creating far more energy than you are actually using.

High Temperature Solar Collectors

Ironically, the high temperature solar collector is not seen as the most efficient as it requires thicker insulation, more cover sheets, or forcing more air from the collector. In fact, of the 3 types of solar collectors it only has a collector efficiency rate of 50% as compared to the 75% of the medium and low.

It should also be noted that studies show that solar energy materials will pay for themselves in 2-3 years and have a life expectancy of 20-30 years.

For additional information on the topic of heating and air visit Abel Onsite.

Article independently authored by Janet M. Slagell. The content herein may or may not frelect the views and opinions of Abel Onsite. Click for search engine optimization and search engine marketing or visit WebDrafter.com's Blog.

How to Save on Your Utility Bills

With these tight economic times, everybody is looking for ways to save money. Your utility bills are an area where you can realize substantial savings with a little thought and effort.

The first area is with your lights in general. Switching all of them to compact fluorescent lamps (CFL's) can add up to significant savings over time. CFLs us up to 75% less energy than a typical incandescent bulb and can last up to ten times longer. The draw back is the up front cost which can be many times the cost of an incandescent. With CFLs you must be prepared to recoup your cost over a few years.

Next, is your water heater. By wrapping it with a hot water heater jacket you can reduce the amount of heat that escapes to the outside air. The jackets are inexpensive at less than $20. The energy savings you realize will depend on the type and size of water heater you have.

Also, you might consider installing an on-demand water heater. These devices only heat as much water as is needed at a particular moment. If hot water is not needed, none is heated. This contrasts to the standard water heater which keeps water at the desired temperature constantly regardless if it is needed at the moment or not. This means the heater must reheat the water over and over as it cools. Imagine how much wasted energy there is while you are work or on vacation! Again, an on-demand system is one in which you will realize savings over time since there is an upfront cost to install it.

The final area where large savings can be realized is with heating and cooling your home. The average home consumes most of its energy maintaining a comfortable temperature - upwards of 40%, in fact. By installing a programmable thermostat you can save up to 30% on your utility bills. These thermostats can be programmed to different temperatures depending on your schedule. For instance, if you leave for work at a certain time, the thermostat can be set to a lower temperature during the winter while you are gone. Instead of maintaining the house at 72 degrees it might maintain it at 60 degrees. Further, it an be set to warm the house back up to 72 degrees thirty minutes or an hour before you arrive home at the end of the day. In this fashion, you are never in an uncomfortable cold house and you save money!

Finally, you might want to consider replacing your air conditioner and furnace if you have old systems. New systems are so much more energy efficient that, coupled with rebates and government incentives, you can start saving a tremendous amount on your utility bills can recoup the install cost in about three years. The difference in energy usage for a new versus and old system can be quite astounding. Call your local HVAC installer to learn more about the specifics.

Hopefully, this article has given you some actionable ideas to help make things a little easier on your wallet!

For additional information on the topic of heating and cooling systems Abel Onsite.

Article independently authored by Eric Parish. The content herein may or may not reflect the views and opinions of Abel Onsite. Click for search engine optimization and search engine marketing or visit WebDrafter.com's Blog.

What Are the 3 Types of Dehumidifiers?

Hot and sultry, muggy and sticky, there's nothing worse in the summer time than the heaviness of the humidity. In fact, for some states it's so bad, that you are drenched in moisture just to take a walk to mailbox at the end of your short driveway. And, when that humidity makes its way indoors, the days and nights can seem virtually unbearable. Fortunately, there is a solution. Invented by Willis Haviland Carrier in 1902, dehumidifiers soon became the ideal way to cool one's home. Over the years the dehumidifier as evolved and today there are 3 main types of dehumidifiers.

All humidifiers work on the same basic principles, though each one varies somewhat based on the type. Like an air conditioner, the dehumidifier uses refrigerant. However, it does not cool the air...it actually warms it slightly which decreases the humidity thus making the room more comfortable. This is done by a fan, hot and cold condenser coils and a water reservoir.

The heat pump dehumidifier is used to pull out water form a building by using a heat pump which works much like an air conditioner pump. A fan is used to move the air across a frigid coil causing the moisture to condense. Then the droplets are collected in a bucket inside the unit. The air is then warmed by a second coil and then released back into the room at a comfortable temperature. The heat pump dehumidifier is considered the best one available.

In large industries, especially those in warmer climates, the most common type is a chemical absorbent dehumidifier. This type uses a chemical drying agent that works with a heat exchange wheel to absorb the water molecules from the air. The process pulls the damp air outside through the vents.

The third type of unit is the dehumidifying ventilator. These work with a sensor controller and an exhaust fan. These are less effective in climates where the humidity is especially high because the ventilators draw outside air into the house. Rather, the dehumidifying ventilator works great in basements but you must pay close attention to how it is working as it can depressurize a room and can cause gas spills...just be sure that if you have a gas furnace that it is properly vented and you will fine.

If you already have a dehumidifier, but it does not seen to be working correctly, there are a few things you can do. First you will want to make sure that it is the right size unit for the space it is cooling; then after you have turned the unit off, check the following:

• Remove the cover clean the condenser and the evaporator coils.
• Lubricate the fan motor bearings, if the motor has oil ports.
• Make sure the humidistat is working properly by testing it with a volt-ohm. Rotate the humidistat's knob as far as it will turn in either direction. If it reads 0 throughout the process then it is time to replace the unit.

For additional information on the topic of heating and air conditioning visit http://www.abelonsite.com.

Geothermal FAQ's - Could a System be Right for You?

As our population grows and the earth's resources are strained like never before, many people have questions about geothermal systems but are not sure about some very fundamental concerns. Hopefully, this brief article can open your eyes to the potential of geothermal system.

How does geothermal work?

The basic principle is that a geothermal heat pump extracts heat from the earth during the winter and pipes into your home. This processed is reversed during the summer. The heat pump pulls the heat from your house and pumps it into the earth. This process is similar to your refrigerator. If you reach behind it you will feel a lot of heat. This heat has been removed from inside the refrigerator and pumped to the outside air.

The heart of a geothermal unit is the system of pipes buried underground to facilitate this heat exchange.

Are there benefits to using geothermal energy?

Yes. Geothermal energy is clean. There is no need for fossil fuels - which reduces our dependence on foreign oil. It is also a renewable resource like solar or wind.

Plus, it is a very cool conversation piece for visitors!

Am I in an area where geothermal can be used?

Unless you live in a very odd environment like the arctic, then you are almost certainly in area where a geothermal heat pump can be unitized productively. That said, there may be local consideration that prevent the installation. An installer would have to evaluate your specific site.

How long does a geothermal system last?

Geothermal heat pumps are very durable. Since the system does not have elaborate complicated parts and is based on a simple principle, your system should last many, many decades.

Would my geothermal system be loud?

Fortunately geothermal systems are very quiet unlike a standard HVAC system.

Will I save money using geothermal?

Yes! It is not uncommon to have heating bills cut by 20% - 50%. However, you will need to remain in your home for several years to recoup the installation costs in annual savings. If you plan on moving soon, a geothermal unit is probably does not make sense from an economic prospective. In general, it will take five to ten years to recoup the installation cost.

There is much more to a geothermal system but these answers should help you get started thinking about whether a system is right for you. The environment might just say "Thank You!"

For additional information on the topic of geothermal heat pumps visit Abel Onsite at http://www.AbelOnsite.com

Pumbing, Heating and Cooling Systems / How Can You Make the Most of Your Home Comfort Systems?

Just as you would not expect your car to run smoothly without having frequent oil changes, tune ups or making sure that there is gas in the tank, you need to make sure that your heating, cooling and plumbing systems are in working order. As Anthony Shaker of UNICCO in Newton, Massachusetts says, "...A solid program of preventative maintenance is absolutely paramount. The better something is maintained the more likely you're going to get the appropriate life-cycle from the equipment."

Heating

• Before the weather actually turn cold, take a few minutes to see if any warm air blows through the vents when the system is turned on.

• Be sure to change the air filters, dirty filter prevent the furnace from working properly and will also result in poor indoor air quality.

• If you have natural gas for your heating system, check t see that the pilot is lit. The flame should be blue, if it is yellow or orange you will need to contact a HVAC professional as this can be the sign of a problem.

• Make sure that there is nothing blocking the vents or filters so that the heat can get into the areas in which it is needed.

Central Air

• If properly maintained, an air conditioning system can least as long as 15 years, so taking the few minutes necessary to check your AC system can ultimately save you time and money.

• Have your duct work checked and cleaned at least once every 3-4 years so that not only will the system work better, but your air will be cleaner.

• Clean off the outside air compressor with water, this is easily done using your garden hose.

• Keep all things away from the compressor so that it has a free flow of air

• Change the filter every 4-6 weeks, or as recommended by your user's manual.

Plumbing

Like your heating and air systems, you will also want to maintain that your plumbing system is in the best working order possible. Here are a few ways suggested by Service Magic that you can do this.

• Shut off the main water valve and drain the system by opening faucets at the highest and lowest points of the house, if you will be gone for several days. In addition, keep the heat on and set no lower than 55 degrees-especially if it is during the winter months.

• During the winter, your water heater works harder. Flush it out and remove sediment buildup, to prevent corrosion, and increase the life span. Drain several gallons from the faucet near the bottom of the tank through a hose directed into a nearby drain.

• In the event frozen pipes, water pressure builds and can cause cracks - regardless if whether the pipe is made of plastic, copper or steel. Even a tiny crack can unleash more than 250 gallons of water in a single day.

• Be sure to clear leaves and debris from downspouts to ensure easy drainage when water freezes and thaws.

Visit http://www.abelonsite.com for information on heating and air conditioning today.


Article independently authored by Janet Slagell. The content herein may or may not reflect the views and opinions of Abel On Site.

Save on HVAC Costs - Caulk and Seal Your Windows For Energy Efficiency

As energy costs increase, people begin to look for ways to lower their personal energy consumption. One of the popular points of improvement are new windows. With advances in technology and materials, windows are substantially better than their predecessors at retaining heat during winter months and keeping the home cooler during the summer. Unfortunately, new windows can be quite expensive! However, there are options if you are unable to afford new windows or would prefer to replace your windows gradually rather than all at once.

Before embarking on the improvement of your current windows, it pays to inspect them. Are there rotten boards, cracked glass or other broken parts? Depending on the condition you might be forced to replace these windows as they are beyond enhancement. Also, consider replacement if your windows were installed before 1978 as they might contain lead paint. Lead is an hazardous substance that should not be in your home particularly if children are present.

If your windows pass muster, you can begin improving them for energy efficiency. One of the cheapest and easiest tasks is to caulk all cracks and gaps around the window frame. Air can seep (and sometimes actually blow) through these gaps. By blocking these pathways you will be taking a big leap toward increased energy efficiency. You will need a caulk gun which will run less than $10 and is very easy to operate even for a complete novice. You will also need a few tubes of caulk which run a few dollars per tube at home improvement stores. Be sure to purchase paintable caulk if you would like to cover the caulk after it has cured.

Actually applying the caulk is very easy. Simply load the caulk tube into the gun, trim off the end of the tube with scissors or a knife and then run a wire down the tip to puncture the foil covering inside. Apply the tip of the tube to the area you wish to seal and slowly pull the trigger. It might takes a few squeezes for the caulk to come out on a new tube. Once it is slowly flowing, move the tip over the crack to fill it up. To smooth the caulk or push it into a new position, wet your finger and apply pressure as needed. Using a dry finger causes the caulk to stick to your finger and tends to make things messier. In a pinch, saliva works just as well!

Also, be sure to pick up weather stripping to fill in gaps around the sash where the window goes up and down. You will need to custom fit the stripping to your windows.

Be sure to inspect your caulk and weather stripping every year to make sure everything is still in working order.

By taking these two simple steps, you have gone a long way toward greater efficiency. Plus, you have save thousands of dollars in the process! That will make anybody feel good.

For more information on your HVAC units, service, & repair or energy efficiency, please visit http://www.AbelOnSite.com.

Article independently authored by Eric Parish. The content herein may or may not reflect the views and opinions of Abel On Site.

How to Extend the Efficiency and Life Span of Your Water Heater by Draining It

When was the last time you thought about your water heater? In all likelihood it was when you ran out of hot water. Fortunately, the lack of hot water only lasted for a few minutes or hours. Could you run out of hot water for a longer period of time? You sure can! If your water heater fails you will be without hot water for several days while waiting for a replacement. Avoid this hassle and give your heater a little tender loving care. Fortunately, it isn't hard to do.

The most important thing to do is drain your hot water tank. Over time, sediment from the water settles on the bottom of the tank. This can cause the tank to rust and to slowly be corroded away until it ruptures. Plus, the extra layer of gunk causes the heater to work harder and less efficiently which increases your gas or electric bill. By draining the tank you remove the gunk and keep the unit working in tip-top condition.

To drain your heater you will need a hose and about an hour or two.

The first step is to turn off the heat source. With an electric heater, you will need to flip the breaker switch to "off". With a gas heater turn the thermostat knob to the pilot setting.

Next, turn off the cold water supply to your tank. The line is typically labeled on the water heater and the shut off is located just above the tank.

Open a hot water faucet somewhere in the home. This will prevent a vacuum from forming in the tank as the water drains.

The tank's drain will be located at the bottom and will have a threaded outlet as well. Attach the hose to the tank and route the other end of the hose to a safe surface for receiving many gallons of hot water. Open the drain valve and watch the water flow! It will be very dirty and brown to start but eventually it will run more clear. Turn on the cold water once the tank is empty to flush out the final bits of sediment. Allow water to flow until it comes out clear. Close the drain valve and the faucet on the sink you opened up.

Allow the tank to fill completely and then turn on the electricity or gas again.

That's it! Very straight forward and simple stuff. Just a few minutes of your time and you extend the life of your water heater. Simply repeat every year and your water heater will thank you!

For more information please visit http://www.ableonsite.com the water heater installation specialists and hvac servicing.

Article independently authored by Eric Parish. The content herein may or may not reflect the views and opinions of Able Onsite Heating and Cooling Specialist.

What is the Best Type of Furnace For Your Home?

From geothermal heating to gas furnaces and electric heaters to wood burning stoves there are many different ways people choose to heat their home. Of course, this warmth does not come cheap. Whether you use natural gas, electric heat or an alternate heat source, heating bills in the winter typically supersede the cost of keeping cool.

So, how can you determine what the best form of heating is? Here are a few considerations to help you before you make a final decision.


Source- If you are building a new home the heating options are more varied as you can go with whatever method will be best for you. However, for existing homes, it may necessary to stay with the type of heat already in use and just change the size and efficiency of the model. For new homes, many homeowners are choosing to use alternative heating methods such as solar heating, absorption heating or geothermal heat pumps.
Cost- Typically fuel is measured in physical units such as gallons or watts with the most common measurement being the Btu (British thermal unit). A Btu is the amount of energy needed to raise the temperature of one pound of water 1o F. Currently, the most inexpensive forms of heating are (from lowest to highest)-seasoned firewood, propane, natural gas and electric heating.
Environmental concerns- In this "Going green" society, many are choosing to use firewood, propane, natural gas or solar heating as it is far more earth-friendly than electric heat since it does not require coal to be burned in order to be used.
Efficiency and Size- A furnace that is too big for a space will cycle off and on more than necessary using more heat and energy and adding higher costs to the bill. When you are deciding on a furnace, be sure to know the dimensions of the space to be heated so that you can select a heat source that will keep the space warm without straining the system and costing you too much money. To ensure the best possible furnace, be sure to look for an Energy Star certified heater.
Talk to a certified HVAC technician or a contractor who is a member of the North American Technician Excellence (NATE) group. They will be able to tell you what type of heating unit and fuel will be best for you home. You may also want to talk to friends and neighbors to get their insight.
If you are still uncertain what type of fuel and furnace will be best and whether or not the investment will actually pay off, use this formula to determine the Return on Investment (ROI): Take your first year savings (or potential savings) and divide them by the cost of installation. The answer will give you an idea of how long it will take you to pay back your savings with your new furnace.

For further information on furnaces for you home, please visit www.abelonsite.com today.

Article independently authored by Janet M Slagell. The content herein may or may not reflect the views and opinions of Abel Onsite Heating and Cooling.

Is Your Air Conditioner Making You Sick?

There's nothing quite like coming inside after a long afternoon in the sun and feeling the cool air provided by your air conditioner. As the cooler temperatures hit your body, you begin to relax and breathe easier. However, this is not always the case. In fact, in recent years, the number of reports about poor indoor air quality has become more prevalent.

According to a study by Cornell University, at least 20% of building occupants have experienced the following symptoms (also known as "sick building syndromes") due to the air quality in homes or work locations:

• Headache, fatigue, shortness of breathe
• Sinus congestion, cough or sneezing
• Eye, nose, throat and skin irritation
• Dizziness or nausea

However, for people who have asthma, allergies, respiratory diseases, a compromised immune system or wear contact lens poor indoor air quality can cause even more aggravation.

Some people often suffer with these symptoms for months not realizing that they are caused by the air inside not the elements outside. If you are not sure whether or not you are suffering from health problems as a result of poor indoor air quality, here are some guidelines from the EPA that can help you determine if you have "sick building syndrome".

• Many people in your office/building are experiencing the same type of problems
• The problems go away when you leave the building or are gone for several days (i.e. over the weekend)
• The problems seem to occur suddenly
• People with respiratory issues, asthma or chemical sensitivities have no problem when outside, but struggle with breathing and have the symptoms listed above when indoors.
• Someone else in your building has already been diagnosed with an indoor air-related problem.

If you are a building owner or manager, then you do not want to be held responsible for any health issues of your employees or residents. To prevent your building from becoming another news story, due to poor indoor air quality concerns, here are several steps you can take.

• Pay attention to your surroundings. Note the air vents in your building. Are they clean? Does there seem to be a moldy or musty smell?
• Ask others around you. Occasionally ask co-workers or other building occupants if they have noticed any changes in air quality, leaks or mold/ musty smells around the vents or ceiling tiles. This can be done via e-mail, surveys, door to door-whatever works best for you to collect the information.
• Keep records. If residents/workers in a particular spot seem to report an above average amount of complaints, you may need to test the HVAC system in that area or call in a professional to do it for you.
• Testing devices are available from many HVAC companies, as well as online. These tests can check for air duct cleanliness as well as allergens and microbial growth.

Taking the time to make sure your AC system is working without causing sickness is important.

For further information on heating and air conditioning, please visit www.abelonsite.com.

Article independently authored by Janet Slagell. The content herein may or may not reflect the views and opinions of Abel Onsite.

Residential Solar Concepts 101

Ah, yes, the summertime! A wonderful time of year for some activities. Nothing could ruin the fun - except maybe the electric bill coming in the mail! It can be so expensive running central air and fans. Is there a way to escape from burdensome electric bills?

In fact, there is a way to escape and it is trendy too - solar! Alternative energy is very big right now and as a homeowner you can get in on the action. In fact, the federal government is giving people a tax credit of 30% of the material and installation costs of a solar system. That is much, much better than a run-of-the-mill tax deduction. The states also have incentives but they can vary widely. In short, now is probably the most economical time the United States has ever seen for installing residential solar systems

Basically, solar powering your home is done by capturing the sun's rays with panels installed on your roof or near your house. The panels convert the sunlight into electricity and then an inverter converts the power from direct current into AC power which is usable by your home appliances.

There are two ways to implement solar power into your home. Off grid and grid-tied. With off grid, your entire home is powered by solar and you do not have a connection to the electrical grid. The power company simply does not exist for you. This is a great way to power your home but it can cost tens of thousands of dollars even with government incentives to install the system all at once. This is difficult for many people to do.

Grid-tied is the more common way for people to power their home. Basically, your house is still connected to electric company but you have solar panels generating electricity as well. The power from the grid is only used if your solar array is not providing enough for your needs at any point in time. Why wouldn't your array provide all of your needs?

It might not provide all of your needs at a given moment because:

1. The sun is not shining

2. You are running many electrical devices at once - which is unusual for your home

3. Your array is only a meant to be a partial solution

If the sun is not shining, your solar panels can't collect sunlight. It might be nighttime, there might be an intense storm or heavy cloud cover. Either way there is no power for you. You can overcome this obstacle by installing batteries with your solar system. The batteries will store excess electricity generated that is not used by your home right away. For instance, if you are on vacation there will likely be surplus energy and the batterie will capture and store it. With batteries, you can still use your solar energy no matter what the sun is doing. The drawback to batteries is that they are an expensive part of the system.

Next, you might be having a giant party with many speakers, stage lights, fans and air conditioners running. With this situation your solar array might be big enough for your day-to-day operations but the excess usage exceeds it capabilities. During these moments, the grid would power your appliances alongside your solar array. Of course, if you have enough batteries, they could kick in and make up the slack.

Finally, the most common reason is that you are building your solar array slowly over time to mitigate paying out large sums of money all at once. For example you might install a system that powers only 20% of your power needs and the other 80% comes from the grid. That is a good arrangement because your power bill will be 20% cheaper moving forward! Plus, you can slowly add onto your system so that it powers 40%, 60% and eventually 100% of your power needs.

As a rough guide, a system capable of 100% powering the average U.S. home would run about $35,000. Keep in mind, however, that this would come with at least $9,000 tax credit (possibly more depending on your state) and you would never have to pay an electric bill again! Plus, you can sell excess power from your solar array back to the electric company. That right - the power company sends you a check! Of course, you have to be grid-tied for this to work.

Obviously, there are many facets to solar power that are beyond this brief article. Hopefully, you have enough information to start thinking about how solar might fit into your life. Maybe you just spend $200 and buy a small solar panel, an inverter, and a marine battery and use this system to charge your laptop. Thats an easy first step toward being energy independent and cutting loose from that ghastly electric bill!

For more information on residential solar power please visit www.AbelOnsite.com.

Article indpendently authored by Eric Parish. The content here in may or may not reflect the views and opinions of Abel Onsite.

HVAC (Heating, Ventilation, and Air Conditioning) Basics

HVAC, (the acronym that stands for Heating, Ventilation, and Air Conditioning) means little more than a creature comfort, necessity, or a stiff repair bill to most homeowners today. Some homeowners don't even know what the acronym stands for in full! That being said, it is the responsibility of every homeowner to both know the basics without having to call Handyman Hank for help.

As the old mantra goes the best place to start is from the beginning, so let's begin by touching on a bit of history of the HVAC field. The systems inclusion in the home began way back in the industrial revolution when new methods of electronics and manufacturing became available, and lets face it, we got tired of sweating at work and at home. Heating and air-conditioning provides proper temperature and higher indoor air quality through mechanical engineering feats that are still being improved upon today.

The first portion of the acronym, heating, is most often used by way of a central heating system consisting of a boiler or furnace to heat water or air, and ductwork that provides a transport medium to move the warmed air throughout a structure. Typically the heating portion of the systems (i.e. radiators, heat pumps) is located in the coldest part of the home in order to provide proper circulation. Unsurprisingly, the invention of central air systems is credited to the ancient Romans, who created ductwork in homes and public baths.

Ventilating, also an important addition to HVAC, consists of the systems that exchanges, replaces, and filters existing indoor air in order to create a higher indoor air quality. Rooms in the home such as bathrooms use a more mechanical form of ventilation in order to reduce humidity and odors, while items such as ceiling fans seek to lower perceived temperatures and draw in fresh air through an open window. Your central air system also most likely uses ventilation in its process and provides high air quality through filters that eliminate and capture dust, mold spores, and other indoor allergens.

Lastly, air-conditioning systems work on the fact that cold air is the absence of heated air. These systems rely on principles such as conduction or chemical refrigerants to remove heat, therefore producing cool air. The ductwork that your central heating system uses is probably also used to disperse this cool air throughout the home. Some systems also use a dehumidifier to lower the temperature of the air as moist air seems warmer than dry air.

Heating, Ventilating, and Air-Conditioning does not have to be difficult, and through a little research you can become more informed and discuss your homes' system with your repairman effectively enough to keep it in working order. Call your local repairman or the manufacturer of your system for tips on how to keep your system running great.

Save on your energy bill today visit www.abelonsite.com for maintenance and service information.

Posted by WebDrafter.com, Inc. with permission.

Article independently authored by Matthew Eddington. The content herein may or may not reflect the views and opinions of Abel Onsite.

Install Radiant Floor Heating for Increased Comfort & Cost Savings

One of life's little nasty surprises is stepping out of the shower onto a chilly floor. Fortunately, you don't have to tolerate this discomfort any longer. With a radiant floor system, you can enjoy toasty warm floors - and many other advantages as well.

Radiant floor heating is a method of keeping a room or house warm by installing the heating elements under your flooring. The systems can be either electric or hydronic. Hydronic systems have been around for many years but are quite involved to install and, generally, not a good do-it-yourself project. They require lots of tubing, water heaters, pumps and other devices. On the whole, hyrdonic systems are best for heating very large areas.

For areas ranging from 300 square feet up to about 3,000 square feet, the low voltage radiant heat system works well. It is composed of 12" wide mesh installed on the sub-floor with the final floor covering installed on top of the mesh. Installation is made easy as the mesh can be nailed through without harming it. Spaces under 300 square feet can be heated with a line voltage system. Such systems are commonly used in kitchens and bathrooms. Rather than mesh, the system utilizes heating cables that are laid out on the sub-floor with the final flooring installed on top. Both of these systems can be installed under carpet, wood, tile, stone or marble. Once installed, both systems should be maintenance free as there are no moving parts or filters to change.

Radiant systems have two major advantages over forced air that make them appealing. The first advantage is cost savings as a result of greater efficiency. With a standard furnace, the air is heated remotely and then pushed to its final location The energy required to push the air adds dollars to your utility bill but does not nothing to heat your house. Further, some of the heat in the warmed air will be lost during transit through your duct work. With a radiant system, a much greater percentage of the expended energy is used to warm the room since heat is being generated where it is needed. This is much more efficient and easier on your utility bill. In fact, many people have reported savings of more than 30%.

The second advantage over a forced air system is comfort. Since the heat is emitted uniformly across the entire floor, cool spots are eliminated. With forced air, the heat enters the room at one or two locations and must then diffuse into the remaining portions of the room. As result, some parts of the room will be warmer than others. In a radiant system, the heat is dispersed evenly providing a more constant and uniform temperature.

The cost to install a radiant system can vary significantly depending on your specific situation. However, $4 to $10 per foot installed is typical with a standard bathroom being under $1,000. On any job, economy of scale will work in your favor meaning that the cost per square foot will go down as the area to be heated goes up.

No matter what your job size, you should solicit at least two estimates from contractors and ask for references. As in any trade, contractor quality can vary greatly so ask lots of questions before hiring somebody. Hopefully, you can now make a more informed decision and be able to retire your fuzzy, bunny slippers. With a radiant floor system, you just won't need them anymore.

For more information and guidance about radiant heat flooring, visit http://www.abelonsite.com. Abel Onsite, located outside Minneapolis, MN, specializes in solar heating, geothermal, HVAC and air conditioning systems.

Posted by WebDrafter.com, Inc. with permission.
Article independently authored by Eric Parish. The content herein may or may not reflect the views and opinions of Abel Onsite.